Tag: braap

Posted on

Bajaworx Enduro Windshield

While reading the internet one day, I came across a post from Bajaworx seeking testers for an Enduro bike windshield.  Bajaworx was looking for folks to give their product some real world testing, and to put it through the ringer to see how performed and held up to months of riding.  I promptly replied to the post, and a few days later I received a neat, tidy package in the mail.  Like the proverbial porridge, the box was not too big, not too small, but just right.  Maybe it’s just me, but it really irks me when I get a pair of gloves shipped in a box you could live out of.  No, Amazon, I did not like your packaging.

Tear open the box from Bajaworx however, and you get a carefully and correctly wrapped shield, complete with a bag of hardware taped in place (nice!) and a clear set of installation and care directions.   The shield comes out clean and free from blemishes, and they even used high quality Makrolon polycarbonate in its construction.   These guys obviously care about what they make and sell.

Start the installation by removing the headlight mask on your bike to install the shield.  You’ll have to punch a few holes in the stock mask, but luckily this part is only about 20 bucks if you need to “rework” it for any reason.  Removing the headlight assembly is as simple as disconnecting the wiring, removing the brake hose guide, and pulling the two rubber mounting straps.

Here’s my first gripe: I’m a klutz and I want a template, darn it!  I’m also borderline OCD, so I needed to get the windshield installed perfectly straight.  Out come the calipers and the sharpie so that I can scribe some lines of reasonable accuracy.  A paper template that I can lay over the bike’s headlight mask and mark out the drill holes would be a welcome addition to the installation instructions.

One of the more refined features that are included with the Bajaworx windshield are the stiffening brackets that help reduce movement of the windshield while under wind load.  Sadly, they stopped short of the mark on my particular bike, so I wasn’t able to use them.  It should be noted that I installed the windshield on a model year this was NOT designed for, so that’s no fault to Bajaworx.

Yet again, Bajaworx’s attention to detail surprises me – in this case the appropriate hardware comes pre-assembled; no digging through a bag of hardware looking for the “#4:  6mm screw – 30mm”, or some such nonsense.  Just select a long or short screw, and assemble one at a time being careful not to overtighten.  Depending on what handguards and other handlebar accessories you have on your particular bike, you may have to spend some time tinkering and adjusting to incorporate this windshield onto your bike so that vibration and rubbing won’t cause part A to eat part B.

Over the last several months I’ve taken the Bajaworx windshield down many miles of singletrack, climbed mountains, and gobbled up hundreds of miles at full chat.  I’ve taken the windshield into some properly hairy scenarios, and I never noticed it; with one exception.  I bottomed out hard in a G-out and let myself get pulled too far forward over the bars.  My chest kissed the top of the shield, but that’s all.  No harm, no foul.  Otherwise, it’s utterly imperceptible until you get up in speed.

Once you’re looking to cover some miles, you will notice well, nothing – and that’s the point.  The shield takes all that wind pressure that would normally be pushing you over backwards and diverts it around you.  When sitting, you will have practically no wind from the neck down.  Unlike other products, this piece accomplishes this in such a way as to maintain smooth, laminar airflow across your helmet.  This means that while your head is still in the wind, it’s not bobbling around and creating a roar.  There’s some noise for sure, but it’s all quite tolerable.

Last but not least is durability.  Unfortunately (or fortunately?) I did not get the opportunity to crash test this shield, so I cannot speak to its performance in that arena.  I would posit that this shield is the least of your worries in a crash, and that because the headlight assembly is essentially rubber mounted, it would likely survive any encounter with the earth.  One area of improvement I would suggest is the brake line routing.  The brake hose on my bike would rub constantly on the two ridges on the back of the shield, quickly developing a ‘smeared’ section.  It’s a non-issue since the shield in nowhere near your sight line, but it’s kinda ugly nonetheless.  Granted, it’s still the best looking plastic on my bike, so who’s to argue?

All said, this is a well thought out, well made, and made in USA product that can provide some real world relief on those long stretches at speed.  Whether you’re headed to Dead Horse, or you’re in search of some fish tacos and a cold cerveza, the Bajaworx enduro shield is a welcome riding partner and will see you through a day of riding with noticeably less fatigue.  Check them out at bajaworx.com.

 Full Disclosure: Bajaworx generously contributed this Enduro Windshield for review at no cost to the author or American Adventurist.

 

Posted on

SIDI Adventure 2 Gore-Tex

Wet feet are one of those things that can really impact your enjoyment of a ride.  In the best case scenario, you’re looking at a minor annoyance when you can dry your feet and all your gear when you get home from a day’s ride.  Yet, ADV rides are typically multiday if not multi-week outings, and when you’re shoving your feet into the same wet gear day after day it can really wear on even the hardiest of riders.  Throw in some cold temperatures, and things can quickly go from ‘adventure’ to suffer fest.  Yet, with the right boots, all of the wet in the world can’t keep you from enjoying an awesome ride.

For the last eight months I’ve been wearing Sidi’s Adventure 2 Gore-Tex boot in desert heat, on frosty fall mornings, through flood inducing summer monsoons, and on plenty of bluebird days.  I’ve worn them on dual sport rides, off road rides, adventure rides, and even spent a little bit of time on a trials bike while wearing these boots.  If this sounds like a lot, that was exactly the point – my objective was to throw as many different conditions and types of riding at these boots to see how they would hold up.

The Adventure 2 is an update of SIDI’s well-loved Adventure Gore-Tex boot, and just as you would expect, SIDI has improved on the original Adventure Gore-Tex boot for this second revision.  One of the most notable changes is that the Gore-Tex gaiter has been extended further up the boot, making it even harder for water to find it’s way to your feet.  Out in the world, that translates into riding in wet conditions without concern for getting wet feet.  You can overcook water crossings for ‘gram-worthy (that’s how the kids refer to a photo for social media) photos, ride in microbursts that turn roads into rivers and just about anything else you can think of.  About the only way you’re going to get wet in the Adventure 2 is if you have to put a foot down in knee-deep water or if your pants aren’t waterproof.

In summer heat that feels like you’re riding in a hair-dryer, the Adventure 2s are still quite comfortable.  Considering that water vapor in the microclimate inside your boot has to go through a Gore-Tex laminate and all of the other materials that make up the Adventure 2, breathability is still quite good, and I’d go as far as to say they’re more comfortable in the heat than other brand’s non-Gore-Tex moto boots I’ve worn in the past.  Make no mistake – your feet are going to be warm, but if you’re worried about feeling like you’re wearing plastic bags on your feet – you won’t get that feeling in the Adventure 2.

In the cold, the Adventure 2 does a good job of keeping your toes warm, even though the boots aren’t insulated.  Toe warmth is obviously helped by having a core body temperature that’s in the right range, and a good sock on your foot, so as long as you have these first two things in place you should be good to go for a ride in the cold with cozy feet.

Extending the Gore-Tex cuff up the boot wasn’t the only revision that Sidi made to the Adventure 2 – the ankle flex system, Achillies protector, TPU placement, and other features have all been updated for this second revision.  You’ll feel these refinements the first time you slip a pair on and notice that the boots already feel (nearly) broken-in.  About the only gripe I can find with the Adventure 2, is that it isn’t a great boot for hiking for miles in.  On several occasions, I’ve found myself going for multi-mile hikes while out riding and on a few occasions this resulted in hot spots on my feet.  But I don’t fault the Adventure 2 for that – after all they’re motorcycle boots and not hiking boots, and there is no way that two buckles and a Velcro closure can embrace your foot the way a proper lace-up boot can.  Therefore, my wishlist for Adventure 3 would be better hiking performance.

In the course of normal amounts of walking around and all day riding, I didn’t have any uncomfortable fit issues.  I could spend nearly all of my time on a long ride standing and my feet would feel great at the end of the day.   With the Adventure 2 as part of my gear system, I stopped bringing extra footwear on my rides (unless I knew I was going to be hiking) as I was quite comfortable living in these boots 24/7.

On the bike, the Adventure 2 Gore-Tex works great transmitting input from your feet to the bike, and at no point on any bike ranging from a trials bike to a big ADV bike did I feel like the boots were impacting my ability to ride.  After a few minutes of riding in these boots, and you’ll feel like you’ve been wearing them for months so there is no learning curve associated with incorporating a new piece of gear into your system.

The SIDI Adventure 2 Gore-Tex boots have been a great addition to my riding gear system.  Even when I’m using the boots for types of riding other than what they’re intended for, they’ve handled everything I’ve done with ease.  Wearing the Adventure 2’s on not-adventure rides started out as a test for the sake of this review, but quickly became a standard practice because I just enjoyed wearing these boots so much – and the whole dry feet thing is pretty nice too.  The Adventure 2 is a well-made boot that has held up great to countless miles of riding, and I only expect continued comfort and worry free performance from them.  SIDI makes some of the best boots out there, and it shows in Adventure 2 Gore-Tex.  They’ve taken the well-loved original boot and only made it better in it’s second revision to create one of the best adventure / dual-sport / keep your feet dry when you’re riding boots money can buy.

Full Disclosure: SIDI generously contributed a pair of Adventure 2 Gore-Tex boots for review at no cost to Chad de Alva or American Adventurist.