Desert Turtle - M1010 Build

Update: I dropped off the radiator at the shop I have used before. It was questionable if boiling it out would not end up causing some pin holes, as it was getting thin in a few areas. Not wanting to deal with this again, I am having it re-cored. I guess this is a really big core as he said it was bigger than most motor homes he does. Core was 34" wide.
 
More work on the M1010. Installing the Paradox By Design cooling kit. Removed the rear water port plates and installed the new ones that allows the lines to connect to the crossover tube. This will regulate flow from the rear of the block, to balance out the temps through the engine. No pic but also installed the new Speedhut gauges oil sender for my dash setup. Had to lay on top of the engine to install all of this.

0101201121.jpg


0101201121a.jpg


0101201122.jpg


0101201229_HDR.jpg


0101201228_HDR.jpg
 
More work and more parts coming in. Here was this weekend's progress. I got my fitting adapters in and was able to finish up the Paradox kit install. One thing the Humvee crossover did was to put the bypass port at an angle to the water pump port. There was not way a piece of hose was going to make that bend so I ordered a molded 45* hose and cut it to fit. Worked perfect. I also received my Fluidampr balancer to replace the stock one. Glad I am doing this as after getting the old balancer off, the rubber ring was split and starting to come out. This was age related failure since it only has 15K on the engine. Rubber and 35 years don't play well together. Waiting for my balancer installer to show up, as I didn't have one with a 16x1.5mm thread insert. Also replaced the glow plug relay on the firewall.

Paradox kit finished up

0104201123.jpg



0104201354_HDR.jpg


0105201526.jpg


Removing the old balancer and pic of the new one to be installed

0105201129_HDR.jpg


0105201128a_HDR.jpg


0102201805.jpg


Glow plug relay

0105201429_HDR.jpg


0105201430.jpg


0105201450_HDR.jpg
 
Last edited:
More work yesterday. My balancer installer came in. I actually used to install the new front seal. Got the balancer installed but still need to torque it. Got the re-cored radiator back and it's nice. Got it installed and then new hoses. I had picked up a NOS lower M1010 specific hose. It has the correct inside spring too. Need to pick up some hose clamps, then fill it up with ELC coolant.

0112200956_HDR.jpg


0112201016_HDR.jpg


0112201124a_HDR.jpg


0109201620.jpg


0112201440_HDR.jpg


0112201509_HDR.jpg


0112201509.jpg


0112201622.jpg


0112201622a.jpg
 
Spent time yesterday modifying the alternator adjusting bracket, since the "Plan B" alts are shaped a little different than factory. You could not rotate them all the way inwards, which made trying to get a belt that was short enough to not max out the adjustment but still be able to go over the pulleys almost impossible. I modified the bracket to extend the adjustment slots and then beefed them up by adding a second stiffing brace. Just need to finish a little clean up and paint it. Should work out well.

0120201133.jpg


0120201221~2.jpg


0120201558.jpg


0120201559.jpg


0120201626.jpg


0120201627_HDR.jpg
 
I think one of my life goals is to buy one of Mike's projects after he gets tired of it. Dude always does ace work, taking care of every little detail.

Thanks @Herbie I do try to send my vehicles to their new homes in much better shape then when they came into my fostering program. :)

I like to do things once and tend to think about reliability and redundancy in my plans.
 
Finally finished up the bracket and getting the correct length belts. Filled with ELC coolant and started to purge the system of air. Got the batteries hooked back up and it fired right up. Started with getting wires ran from the new senders to inside the cab so they will be ready to go when I start the gauge panel install.

0125201619_HDR.jpg


0125201619.jpg
 
Got some free time to start back on my gauge project. Since removing the factory gauges, I lose a few idiot lights that would be important to have. Since I didn't want to just put some LED lights and labels, I was looking for a better option. K-Four switches makes Legend indicators. I bought ones that say Brake, Low Coolant and Four Wheel Drive. Now a place to put them. The M1010 voltage gauge panel has an extra light to indicate the rear door is open. I am not worried about that and this would be a great spot for them. Since the M1008 doesn't have this light, I was able to get a member on Steel Solders to send me this version. Here is how it turned out.

0208201045a.jpg


0208201113.jpg


0208201127_HDR.jpg


0208201434_HDR.jpg
 
Time for an update. I basically finished up the install of the gauges and am very happy how they turned out. Here are some final pics of the install for them.

Modified the original lens cover so I could have it cover the shift indicator and mounted an LED to shine down to light it.

0229200921_HDR.jpg


0229200921a_HDR.jpg


Installing into the dash

0229201027_HDR.jpg


Installed and working

0301201058_HDR.jpg


0301201058.jpg


0323202038.jpg
 
Another project I finally got completed was a rear view camera setup. I found this cool touch screen mirror setup on Amazon and thought this would be a nice way to setup the M1010. It straps to the vehicle mirror (I happened to have a spare windshield mounted mirror in my parts) and you run wiring for power, GPS and the camera. This is a cool unit that not only has the rear camera but a built in dash cam. You can even split screen it. You put in a Micro SD card so it will record while driving as well. I bought the hard wire power adapter (comes with a cigarette plug standard) and the extra long camera cable (original one works great for a car but not a long bed type truck). I ran all the wires and since there is no headliner to hide the wires in, I used woven mesh split loom and put all the wires into that. Then I used wire clamps that I riveted to the header, running the wires along the windshield gasket, then ran down the A-pillar into the dash. I also made a bracket to mount the camera on, that mounts to the rear bumper where I removed the trailer plug that had been installed previously, that I am not using. This works great and it is nice to see what is behind me, especially when backing up.

0404201500_HDR.jpg


0404201500a_HDR.jpg


0404201309.jpg


0404201314_HDR.jpg
 
Another project I finally got completed was a rear view camera setup. I found this cool touch screen mirror setup on Amazon and thought this would be a nice way to setup the M1010. It straps to the vehicle mirror (I happened to have a spare windshield mounted mirror in my parts) and you run wiring for power, GPS and the camera. This is a cool unit that not only has the rear camera but a built in dash cam. You can even split screen it. You put in a Micro SD card so it will record while driving as well. I bought the hard wire power adapter (comes with a cigarette plug standard) and the extra long camera cable (original one works great for a car but not a long bed type truck). I ran all the wires and since there is no headliner to hide the wires in, I used woven mesh split loom and put all the wires into that. Then I used wire clamps that I riveted to the header, running the wires along the windshield gasket, then ran down the A-pillar into the dash. I also made a bracket to mount the camera on, that mounts to the rear bumper where I removed the trailer plug that had been installed previously, that I am not using. This works great and it is nice to see what is behind me, especially when backing up.

View attachment 51163

View attachment 51164

View attachment 51165

View attachment 51166

Mind sharing which mirror setup you purchased? I've been looking at them lately as seeing through my camper shell and out the tinted rear window is tough. I've been considering going this route and have been looking at this one: LINK.
 
Well I haven't had a lot of updates on the M1010 as I got sidetracked on another project we picked up mid Feb, a '48 Chevy Stylemaster 2 door sedan.

ramona4-30-20.jpg


But on to the project for today. I have been wanting to get the Wrangler seats installed and finally had free time. I pulled the drivers seat and after a bunch of measuring, it looked like I could use the factory brackets and make some cross bar pieces and bolt everything together. Overall it went well but after getting it installed, with the stock brackets, it sits about an 1" or so too high. I'll need to fab up my own mounts and get this lowered. I think once I can do that (which I need to get metal as I don't have what I need) these will work out very nice.

0524201230_HDR.jpg


0524201230.jpg


Needed to cut this bracket piece off, from the Wrangler seat.
0524201337.jpg


0524201406_HDR.jpg


0524201550_HDR.jpg
 
Update from Memorial Day project. My best friend got me a hookup on some Thunder Sky LifePo4 lithium batteries. First order of business is to reduce the pack down to 4 cells, to make a 12v pack. That was a PITA as I had to re-bend and drill 16 straps. Being stainless steel, this was not a simple project. My plan was to put them into plastic ammo cans. I happened to find some on Amazon that looked like they would work perfectly. Once dropped in, I cut the included tray to make a cover over the top of the cells. Now I need to order a couple BMS units to manage each pack. They will sit on top of the covers. Each pack is 100Ah so 200Ah total. These should work out great.

0525201006.jpg


0525201126_HDR.jpg


0525201128.jpg


0525201129.jpg


0525201155_HDR.jpg


0525201200.jpg


0525201327.jpg
 
Back on the seat project this past Saturday. Pulled the seat back out and was figuring I would need to make a new set of floor brackets and use the sliders from the Jeep seats. After getting it out, I realized the Jeep sliders did unbolt from the seat (I thought they were welded on). By removing them and then modifying my brackets on the stock GM sliders, I was able to mount the seat directly to them and in turn, dropped the height a little over an inch. This ended up being perfect and puts the seat at the correct height in the truck. Even the Jeep "seat lift" system still works. Now need to figure out the passenger side, as this does not have sliders. That seat is a fixed mount. Could be interesting.

0530201205a.jpg


0530201205.jpg


0530201205_HDR.jpg


0530201524.jpg


0530201530_HDR.jpg


0530201530a_HDR.jpg
 
Back on the battery project. I got the rest of the parts I needed and completed one of my two battery banks I am building. I wanted something very clean looking, serviceable and not looked all hacked together. I purchased two 120Ah BMS units from Overkill Solar off Amazon. He is a member on the DIY Solar Power Forum, which is where I did a LOT of my research at. It was tight getting everything to fit but it all does and should work well. This BMS is fully programmable and does have a low temp cutoff (and high temp). LifePO4 cells can be damaged if you try to charge them below freezing. This is the newer model that has the port for a switch to turn off the discharge side, so if in storage for a while, nothing will be drawing from it, other than the BMS. If I really need to power it down, I just disconnect the balance plug and that effectively powers it off. Very happy with how this turned out. Now I need to finish #2.

BMS unit
0601201840.jpg


3/8" terminals
0608201318.jpg


It's a tight fit and the cable need to route correctly but it all fits
0608201439.jpg


Wiring done, terminals and cutoff switch installed. BT module taped down.
0608201509.jpg


All closed up and ready to use
0608201510a.jpg


Here are three screenshots showing the discharge status (on or off) as I change the switch. Also showing all 4 cells very balanced. This is from the Android app, where you can change all types of settings.
BMS Info.jpg


Outside of finishing the second pack, this project is done.
 
Had a busy but good weekend on the M1010. Saturday I set out to build the mounting system for the passenger side seat. After pulling out the original seat, I ended up using the two rear "feet" off of it but found the front ones were too high, since I was going to use the Wrangler sliders. Originally the pass. seat does not move. Broke out the C channel and tools of destruction and went to town. About six hours of fab work and I ended up with a mount that located the seat on the same planes as the driver side. It is nice and strong. Got it all mocked up and then fully welded but ran out of time and energy to paint it. Figured that was a Sunday project and to get it installed. Saturday night, my Sunday plans changed direction. I happened to be randomly searching on FB Marketplace and ran across an ad for a Gear Vendors OD unit at a great price. It was almost new and the owner found that with the gearing and large tires on his '63 Chevy 4x4, he didn't need it. I contacted him and setup a time to meet. This was a 2 1/2 hour drive north, 280 miles round trip. I am beyond stoked to pick this up. It even was the setup with the fixed yoke output which is exactly what I wanted. I need to get the NP208 adapter as this has the NP205 one. This was a huge score and will make driving so much nicer. It came at a good time as I recently took video, using a "Go-Pro" type camera, of the driveshaft trying to find out my vibration. I have a slightly bent driveshaft so I was going to need to deal with that. Now I can just put in the one needed for the OD unit.

0620201109_HDR.jpg


0620201554.jpg


0620201714.jpg


0620201636a_HDR.jpg


0620201636b_HDR.jpg


Great score!!!

0621201641_HDR.jpg
 
Update: Picked up the Gear Vendors NP208 adapter from them last Friday. Spent about 2 hours Saturday morning doing the mechanical install of the OD. Just ordered a new, custom made driveshaft and hope to have it by the end of the week. Need to do the wiring and top off fluids. If all goes well, might have this all wrapped up over the 4th weekend. Here's some progress pics.

Old NP208 slip yoke housing and driveshaft

0627200950_HDR.jpg


0627200953_HDR.jpg


The GV NP208 adapter and the OD unit itself

0627201017.jpg


0627201017a.jpg


Old rear housing removed, the new adapter installed and then the OD

0627201017_HDR.jpg


0627201151.jpg


0627201213_HDR.jpg
 
Finished up the wiring on the overdrive this weekend. Didn't take any pics of that as it was not really anything noteworthy. Overall it is very simple since the controller has all of the wires plug in, with color codes. Time was looming up and routing but overall came out nice. Most tedious was filling the OD with fluid and topping off the transfer case, which apparently was low. I do have a vibration between 2000-2400 rpm's that goes away below or above that, so I still need to sort that out. Yoke angles are within spec so not really sure where the problem is. I did get out and test drive it and even out on the freeway. I am able to cruise at 65mph at the same rpm of 55mph. I also was able to get up to 75mph for a short stretch. I love that in autodrive it works just like a normal 4 speed auto. Trans runs through the first 3 gears like normal and at 40mph the OD kicks in. Unless I manually override it (with a foot switch) it will disengage at 25mph. It also has a 4x4 lockout so you cannot engage when you are in 4WD. Here's a quick video I did on my test drive showing it going into OD and then showing the RPM change when I turn it off and on with the foot switch.

 
Back
Top Bottom