2018 Lexus GX build

Once the control pack was bolted down and wired up it was just a matter of installing the Hawse fairlead (temporary) and spool the winch line on. I will be installing a roller fairlead as synthetic winch line does not like heat and when you drag the line across the Hawse under load it creates heat and will melt the rope.

964CA18E-945F-4BF6-A245-7D22B60FBB40.jpeg
BA106A98-514D-4B34-8091-6C7180776133.jpeg

78FCD79E-C6DC-4FBA-ACBC-5AD091B40C71.jpeg

3A70842C-D97A-41AC-A434-4D4DD63759A2.jpeg

D2010FF2-9685-444B-8FD1-7BCF13D6EE3A.jpeg
 
Last edited by a moderator:
Part of the problem with modern vehicles is the pedestrian crash mitigation and the Lexus serves it up by having a large snout. This in turn causes manufactures to place the winch mount way back almost out of site as close to the frame as possible. This is a problem when winching and watching the life feed on the drum. It also causes issues for engaging and free spooling the winch. Part of the mitigation was moving the control pack to the bumper shell but I also needed to cut a access hole in the under hood plastic trim to engage the winch. Yes I'll need to pop the hood to do so. If I should need to correct an entanglement I can pop the trim off in a matter of seconds. So out came the 4 1/2" hole saw.

ADB10B12-5803-47A2-A778-6FDFAF9CB167.jpeg
1CE9A9B5-CC38-47F7-A292-16CC276A140E.jpeg
 
Last edited:
Overall I am very happy with he results. It is a compromise for sure in the hardcore winching situation but I've mitigated the pit falls and this will allow me to demonstrate the real issues on contemporary bumper design and what can be done to mitigate the issues.

I really think I need to purchase some black anodized bolts for the control pack mount, OCD?
 
Last edited:
I heard from Sonoran Steel this mornin, should have my suspension by the 10th.

This weekend will be the roof rack and a rear factory receiver hitch.
 
I had a couple hours before work today so I was able to mount my HAM radio mounting plate, base radio and connect wires.
Still need to route all the wiring, antenna coax and clamp everything up.
This one of those little projects I can chip away at.

09E080FA-6D68-46D5-96CB-F63DD7C0C56B.jpeg


172D9303-8518-4653-86D7-7BE592518151.jpeg


E8D68608-633B-4782-A78D-9BFDF29BC0A1.jpeg


40C30444-8D61-43A5-88C1-6F61B51590E3.jpeg


70197B08-BC20-4AAF-98C0-67F5410159D7.jpeg
 
Last edited by a moderator:
All second gen GXs have KDSS. Some have voiced disdain for KDSS but with some study it’s a very intelligent system that is misunderstood. Essentially it’s a passive stabilizer bar disconnect. The hydraulic actuators lock the stabilizer bars at high speeds and smooth surfaces enabling better highway handling. When driving slowly and uneven surfaces the hydraulic actuators sense the pressure differential and allow the stabilizer bar to move freely allowing more suspension flex or droop. [/QUOTE said:
This sounds just like the ACE system on my 1999 LR Disco 2.
 
With no great rear bumper options and wanting a bit for a possible custom build I needed a rear recovery point. My GX didn’t come with a receiver hitch. Wanting to be able to perform some light towing as well as recovery I felt the factory hitch was the best option. Found a Lexus dealer on Amazon. Great experience with them.

The hitch came with all the hardware and bracket to relocate the trailer hook ups.

Used the floor jack to position it in place.
3B662F8F-F3C2-4D4C-B436-4BA71C053CEC.jpeg
867BCABA-D1EE-4CF2-A2DC-230B7C30873A.jpeg
B75CEA9D-7A2F-4AE4-955A-80ABF97B39B7.jpeg
47FF1AD3-E28D-48AD-8607-7D7C886CD919.jpeg
 
The shipping companies came though and all my suspension parts arrived last Thursday!

I went with Sonoran Steel full flex kit for the 5th gen Runner with KDSS. The GX are similar suspension wise just heavier.

I went with Sonoran Steel for a few reasons.

1st. One of two companies that would talk to my specific needs of spring rates and matched shock valving.
2nd. The unique rear axle pan hard/trac bar that they developed to allow full articulation of the rear axle without contact of the KDSS components.
3rd. Steve the owner helped me on my Taco suspension and with the purchase and suspension on my daughters third gen 4 Runner.

The front suspension is pretty standard Toyota with the exception of 700# constant load springs and Radflo resi shocks valved for this spring rate.

The rear suspension has the 850# OME constant load springs, Radflo remote resi shocks valved for the weight and 1" extended down travel that is afforded by the KDSS and the Pan Hard/trac bar. I also ordered the extended bump stops and lower links.

Working around the KDSS system was a learning experience but nothing I couldn't overcome.

11A7FCFE-80FC-4022-B3C5-3C419D5FFD16.jpeg


586495EA-2CBB-4071-B702-D6A7EB0F1DFD.jpeg


BDF841DE-741F-4EF8-8D66-1CD40BAF3000.jpeg


377E8340-FAF6-424D-A596-CE1EABB74BBC.jpeg


B4A6E5EA-9747-450E-ABDD-3ADB5E128F87.jpeg
 
Received word from Truckvault that my drawer platform build will be done on the 17th!!! Bad news I can’t pick it up until at least May 4th or later once the restrictions are rolled back.
 
The roof rack of my 4Runner would actually brush the rubber flap of the door seal when I pulled into the garage.
 
Back
Top Bottom